owlleft.blogg.se - Goodsync cloud

#Goodsync cloud install
#Goodsync cloud full
#Goodsync cloud software
#Goodsync cloud windows

Your server is now configured for GoodSync Connectĭo you want to configure GsServer service (run as daemon) ? y Uncompressing GoodServer for Unix/Linux version 9.9.52.9 100%Įnable GsServer Web UI on port 11000 ? y Gs-server: Profile at /home/root/.goodsync/serverĮRROR: failed to configure server: Cannot set admin: GoodSync Connect UserId cannot contain character ‘P’, it can be only a-z 0-9 _ root # sh.

Stopping existing instances of GsServer…ĭo you want to run GoodSync Connect Setup ? yĮnable GsServer Web UI on port 11000 ?.

GoodSync for Linux 9.9.52.9 armv5_marvell SetupĪRMv7 Processor rev 1 (v7l) – Linux 3.10.39 #1 SMP Fri Apr 29 10:11: 2014T30p5 Build-gitf66ddae3 armv7l unknown unknown Uncompressing GoodServer for Unix/Linux version 9.9.52.9 100% = sh: /etc/init.d/goodsync-server: not root root # sh.

#Goodsync cloud install

sh: /etc/init.d/goodsync-server: not foundīTW, here is also one of the install attempts:īusyBox v1.20.2 ( 15:28:01 CST) built-in shell (ash)Įnter ‘help’ for a list of built-in root # root root # /etc/init.d/goodsync-server start Our model is Busybox-based, but the suggested command also root # /etc/init.d/goodsync-server start I had no idea that the M圜loud family had such a varying set of firmwares across until I received the unit, and had (apparently errantly) assumed the Goodsync folks would have specified if only certain versions were supported. In this case use the following command to start GsServer manually:Ĭpt_paranoia, The goodsync page was all I went off of. Installer may fail to update-rc.d if you are running Busybox-based firmware. I note the Goodsync page you linked isn’t explicit about which of the many variants of the M圜loud family of devices it is intended for (WDCloud, M圜loud, Mirror, DL, EX2, EX4, Pro)

As I understand it, Goodsync is paid for software, so if you’ve paid for it, go and get support for their product. If it was Goodsync, then I’d suggest asking them.

The lower-end devices don’t officially support the installation of ‘apps’.

#Goodsync cloud software

Since WD don’t officially support the use of SSH to install packages on the M圜loud (of any variant, I don’t think), it seems unlikely they’d be advocating/promoting the installation of software that must be installed via SSH. Listed as compatible by whom…? WD? Goodsync? Purchased the 4100 as it was listed as compatible with goodsync, and now we’ve wasted over 6 hours and can’t get goodsync to run

GoodSync checks for new changes approximately every 3 seconds, this time quant is configurable.

On File Change initiates Analyze and Sync, which results in locking of sync folder by GS lock files.

If these changes are result of our own sync, they will produce no new changes to be synced.

If changes occur during Analyze/Sync, they are still detected and sent to the next Analyze.

We recommend to set it to at least 120 seconds (2 minutes), so that GoodSync does not start syncing until files were stable for at least 2 minutes. Note that if you had several changes (including changes performed by this or other sync jobs), the delay countdown will start with the last change that was detected. If not zero then GoodSync will wait this many seconds since the last change detected by On File Change, before starting the Analyze and Sync.

If only one side of the job can be monitored, then GS will get changes only from one side.

None of traditional server file systems can be monitored: FTP, SFTP, S3, SkyDrive, etc.

Any of the above file systems, remotely accessed via GSTP protocol used in GS Connect.

#Goodsync cloud windows

Windows shares, except some broken NAS shares that do not report changes.Windows File System, local disks, except root folder.These files systems can do file monitoring, so they can do On File Change Real Time Sync:

#Goodsync cloud full

Full Analyze is performed only on the first iteration of Real Time Sync.It Analyzes only files that were reported changed by file system, no full Analyze.

Our new Real Time Sync mechanism performs On File Change synchronization: From the Goodsync website:Īnalyze and Sync this job when any file changes in left or right sync folder or its sub-folder. It appears one has to enable the “on file change” option for the real time sync function to work.